Shower Valve and Cartridge Replacement Cost in Canada

By Oleksandr Potapenko · 2026-11-16 · How we research prices

Plumber replacing a shower valve cartridge with the trim plate removed in a bathroom

A shower that drips, runs cold when the toilet flushes, or will not turn off has one part at the centre of it: the cartridge. Angi puts a complete shower valve replacement at 150 to 550 USD, averaging about 350 USD, and a cartridge alone at 100 to 400 USD, averaging about 275 USD. HomeGuide puts the cartridge at 100 to 350 USD, including materials and labour, and the full valve at 225 to 575 USD, with difficult jobs reaching about 900 USD. This Old House puts a typical cartridge swap at 200 to 400 USD, averaging near 300 USD. Converted at 1.39, the cartridge job lands around 140 to 555 CAD, averaging about 380 CAD, and the full valve around 210 to 800 CAD, averaging about 490 CAD. The part itself is small money: a cartridge costs 10 to 80 USD depending on brand, with a Delta RP46074 at about 71 USD and a Moen 1222 Posi-Temp at about 72 to 89 USD. The labour is the rest, and the wall is what makes the labour expensive. There is no Canadian national series for shower valve work, so these converted US figures are checked against Canadian plumber rates of 105 to 175 CAD per hour: a one-hour cartridge swap plus a 15 to 110 CAD part reproduces the same band.

The cartridge is the internal gate that controls flow and the hot-cold mix at the handle, and it is the part that wears out. Inside it, ceramic discs or a pressure-balancing spool slide against each other every time you turn the handle, and after years of hot water and mineral deposits they stop sealing. The symptoms are specific. A shower that drips from the head when it is off is a cartridge that no longer seals. A shower that goes scalding hot or ice cold when a toilet flushes or a tap opens elsewhere is a pressure-balancing cartridge that has stopped balancing, which is also a safety problem: the balancing spool exists to prevent scalds, and when it sticks, the protection is gone. A handle that is stiff, that will not turn fully, or that turns without changing the temperature is a cartridge that has seized or broken inside. All three are cartridge problems, and all three are fixed the same way: pull the old cartridge, match it exactly, and put the new one in.

Matching it exactly is the whole job, and it is where DIY attempts most often fail. Cartridges are brand-specific and not interchangeable. A Moen cartridge will not fit a Delta valve. A Kohler cartridge from one era may not fit a Kohler valve from another. The model number is on the cartridge itself, and the only reliable way to identify it is to pull the old one out and read it, or to photograph the valve and the trim and take both to a plumbing supply house. HomeGuide's brand table makes the point with prices: an American Standard cartridge costs 15 to 50 USD, a Delta 20 to 80 USD, a Moen standard 15 to 50 USD, and a Moen Posi-Temp 60 to 80 USD, and the total installed cost follows the part. Buy the wrong cartridge and the plumber makes a second trip, or the shower stays apart while the right one is ordered. Some manufacturers warranty their cartridges for life, so check before you pay: Moen and Delta both cover many cartridges under lifetime warranty, and a free part turns a 400 CAD visit into a 250 CAD visit.

The decision between a cartridge and a full valve is the decision this guide exists to make. Replace the cartridge when the valve body is sound, the problem is a drip or a temperature issue, and the cartridge is available. That covers most jobs, and it is a one-hour visit with no wall damage. Replace the whole valve when the body is corroded, when the cartridge is seized in place and cannot be removed without breaking the body, when parts are discontinued, or when you want a different valve type, such as a thermostatic valve with separate volume and temperature controls. A full valve replacement means opening the wall, because the valve body sits inside it, and the wall repair is a separate trade and a separate bill: tile work or drywall and paint on top of the plumbing. The access panel on the other side of the wall, if one exists, is the difference between a 500 CAD job and a 1,200 CAD job. If you are renovating the bathroom anyway, replace the valve then, when the wall is already open, and choose a common brand so the next cartridge is on a shelf somewhere.

One more thing to check while the plumber is there. A shower valve that is more than about 15 years old and has never had its cartridge changed is living on borrowed time, and the cartridge that seizes in place is the one that turns a cartridge job into a valve job. Ask the plumber to exercise the shut-offs, check the pressure, and confirm the valve brand and model for the next time. Our guide Leaking Faucet Repair Cost in Canada covers the same cartridge logic for the sink, where the job is easier because the valve is under the sink and not in the wall, and Main Water Shut-Off Valve Replacement Cost in Canada covers the valve that lets you isolate the shower without shutting off the house. Check the numbers in the RepairPrice home calculator (home-calculator.php) before you authorise the work.

Common questions:

Q: How much does it cost to replace a shower cartridge in Canada?
A: A professional cartridge replacement runs about 140 to 555 CAD, averaging about 380 CAD, based on Angi, HomeGuide, and This Old House figures converted at 1.39. The part costs 15 to 110 CAD by brand; the rest is about an hour of labour.

Q: How do I know if my shower cartridge is bad?
A: The shower drips when off, the temperature swings scalding or cold when another tap opens, or the handle is stiff or turns without changing the temperature. All three point to the cartridge.

Q: Can I replace a shower cartridge myself?
A: Yes, if you can identify the exact cartridge model and the old one comes out cleanly. The risk is a seized cartridge that breaks in the valve body, which turns a cartridge job into a full valve replacement. If the handle has not moved freely in years, call a plumber.

Q: Should I replace the cartridge or the whole shower valve?
A: Replace the cartridge when the valve body is sound and the part is available: it is an hour with no wall damage. Replace the whole valve when the body is corroded, the cartridge is seized in place, parts are discontinued, or you want a thermostatic valve.

ServiceTypical range (CAD)Notes
Cartridge replacement, installed140–480Part 15–110 CAD by brand; labour 1 hour
Full valve replacement, installed350–800Valve body inside the wall; 2–3 hours
Full valve + wall opening and repair550–1,500Tile or drywall access and finishing
Moen 1222 Posi-Temp cartridge (part only)85–120Manufacturer list price; Delta RP46074 about 100 CAD
Diagnostic visit125–200Separates a cartridge job from a valve job

About the author

Oleksandr Potapenko

Oleksandr Potapenko β€” founder of RepairPrice, a Canadian price-transparency platform for car and home repairs, based in Edmonton, Alberta.

Check the fair price

See what this repair should cost for your car in seconds.

→

Check my quote

Got a number from a shop? Find out in 30 seconds if it is fair.

→

Related guides