Washing Machine Repair Cost in Canada
By Oleksandr Potapenko · 2026-11-16 · How we research prices

A washing machine usually fails in one of four ways, and each one has a different price tag. It will not drain, it will not spin, it leaks, or the electronics give up. Knowing which one you have before the technician arrives is worth real money, because the cheapest fix of all is the one you do yourself in five minutes.
HomeAdvisor puts a typical washing machine repair at $125 to $450, averaging $180. Fixr puts the national average at $150 to $400. The two guides agree closely, which is reassuring, but the averages hide the spread that matters: a drain pump is a mid-range job, a control board is a bigger one, and a drum bearing can cost more than the machine is worth. Cinch Home Services, summarising HomeAdvisor's 2026 guides, adds the detail that minor fixes such as an inlet valve start around $50 US, while the full range reaches $900 US for a drum replacement, and that front-load models cost more to repair than top-loaders, running $100 to $400 US for the same class of job.
There is no single Canadian national price series for washer repair, so the Canadian figures here are estimates converted from those verified US figures at 1.40 Canadian dollars per US dollar, then cross-checked against named Canadian shops. HomeAdvisor's $125 to $450 becomes roughly $175 to $630 Canadian, with the $180 average at about $250. The Canadian cross-checks sit comfortably inside that band. Appliance Forever in the GTA puts most washer repairs at $150 to $450 all-in, parts, labour and a written 90-day warranty included, with a drain pump at $180 to $320 and a control board at $280 to $420. The exception is a worn drum bearing, at $450 to $650 or more. Number One Appliance Service in Vancouver charges a flat $149.95 diagnostic, 100 percent applied to the repair, and puts a drain pump at $250 to $330 and a drum bearing on a front-loader over eight years old at $600 plus. The GTA and Vancouver shops agree with each other and with the converted US guides: most washer repairs are $150 to $450, and the bearing is the job that breaks the budget.
Start with the drain problem, because it is the most common call and the most fixable. Before you book anyone, clean the drain pump filter, usually behind a small panel at the front base of the machine. Coins, bobby pins, baby socks and lint collect there, and a blocked filter stops the machine from draining at all. It costs nothing and takes five minutes. If the filter is clear and the machine still will not drain, the drain pump itself is the usual suspect. The part is not expensive: Reliable Parts lists a Whirlpool washer drain pump at $40.37 US and a Samsung one at $108.28 US. What you pay for is the labour to reach it, which is why the installed price in the GTA is $180 to $320. A lid switch or door latch is a similar story, with parts at $20 to $70 US and a professional repair typically at $100 to $250 US. Tech Angels in Vancouver puts the same numbers in Canadian terms: a drain pump part at $50 to $150, with professional installation at $150 to $350 in total.
A washer that will not spin, or shakes violently enough to walk across the floor, is usually a balance or suspension problem. Check first that the load is balanced and the machine is level, because an unbalanced load of towels will defeat any machine. If the shaking persists on every load, the shock absorbers or suspension rods are worn. A belt is a cheap part and a quick job; bearings are the opposite. Bearings cost $150 to $200 US for the part alone according to HomeAdvisor's data, but the labour is heavy because the technician has to pull the whole drum out, which is why the GTA price reaches $450 to $650 or more. On a washer near its 10- to 13-year lifespan, that repair rarely pencils out, and both the GTA and Vancouver shops say so plainly: a drum bearing on a front-loader over eight years old is usually a replace, not a repair.
Leaks deserve urgency that other faults do not, because a washer leak is a flood risk. Turn off the water supply valves behind the machine first, then look at the hoses. Rubber inlet hoses age and burst, and they are the single most common cause of laundry-room water damage. Replace them with braided stainless-steel hoses, check the door boot seal on a front-loader for tears and mould, and check the drain hose for kinks and cracks. A door boot seal is a mid-range repair; a cracked outer tub is not worth fixing on an older machine.
The control board is the repair that most often surprises people, because the part itself can cost $150 to $400 US and the total repair $250 to $550 US. On a machine under seven years old, HomeGuide's rule of thumb applies: repair if the machine is under seven years old and the repair is under half the cost of a new one. On a machine over ten years old, a $400 board plus labour is usually the moment to shop for a replacement, which runs $445 to $2,300 US for a new washer according to HomeAdvisor's pricing guide, or roughly $620 to $3,200 Canadian at 1.40.
Ask for a written quote, confirm the diagnostic fee is credited, and ask how long parts and labour are warranted. Ninety days is the standard quoted by GTA shops. Then use the RepairPrice home calculator (home-calculator.php) to compare the quote with the cost of a new machine, and read the companion guides: Dryer Repair Cost: Not Heating in Canada, because a washer repair is often the moment to look at the matching dryer, Appliance Repair Visit Cost in Canada: Repair or Replace? for the 50 percent rule in full, and Dishwasher Repair Cost in Canada for the other water-connected appliance in the house.
Common questions:
How much does washing machine repair cost in Canada? Most repairs run $150 to $450 Canadian, based on Appliance Forever in the GTA ($150 to $450 all-in) and converted from HomeAdvisor's US $125 to $450 at 1.40. A drain pump is $180 to $320 in the GTA; a control board $280 to $420; a drum bearing $450 to $650 or more.
Why won't my washing machine drain? The most common cause is a blocked drain pump filter, which you can clean yourself in five minutes from the small panel at the front base. If the filter is clear, the drain pump itself has usually failed. A pump replacement runs $180 to $320 all-in in the GTA.
Is it worth repairing a 10-year-old washing machine? It depends on the part. A pump, belt or lid switch at $150 to $350 is usually worth it. A drum bearing at $450 to $650, or a control board at $400 plus, usually is not, because the machine is near its 10- to 13-year lifespan and a new washer starts around $620 Canadian.
How long do washing machines last? About 10 to 13 years, according to HomeAdvisor's lifespan data. Front-load models cost more to repair than top-loaders for the same class of job, and their drum bearings are the most expensive common failure.
| Problem | Typical repair range (CAD) | Likely fix |
|---|---|---|
| Won't drain | 200β450 | Pump filter, drain pump, hose |
| Won't spin / shakes violently | 200β500 | Balance, shocks, belt, lid switch |
| Leaking | 200β500 | Hoses, door seal, inlet valve |
| Control board failure | 400β800 | Compare with replacement on older units |