Knob-and-Tube Rewiring Cost in Canada

By Oleksandr Potapenko · 2026-11-16 · How we research prices

Electrician rewiring an old house replacing knob and tube wiring

Knob-and-tube is the oldest wiring still live in Canadian houses, and it is also the wiring most likely to decide whether you can buy, sell or insure a house at all. It was the standard from the early 1900s to the late 1940s: single copper conductors run separately through the framing, held off the wood by white porcelain knobs and passed through joists in porcelain tubes, with no ground wire anywhere in the system. The wiring itself, installed properly and left alone, was safe for the loads of its day, which were a few lights and perhaps an icebox. The problem is what has happened since: eighty to a hundred years of heat, brittle cloth insulation, amateur splices into modern cable, oversized fuses, and insulation blown over wires that were designed to cool in open air. The Insurance Bureau of Canada says insurers will ask about knob-and-tube or aluminum wiring and about service under 100 amps, and that updated wiring, a minimum 100-amp service with breakers, or an electrical inspection by a licensed electrician may be required. In practice that means three answers: no, yes after an inspection, or yes for a set period while you replace it.

The cost is set by size and access, and the Canadian numbers are consistent across sources. NoRadiation, an Ontario electrical inspection firm, estimates that fully replacing knob-and-tube in a typical Canadian home commonly costs $8,000 to $15,000, while larger or more complex homes can reach $25,000 to $50,000 or more, at roughly $10 to $22 per square foot. ElectricSafe, another Canadian contractor source, puts the range from about $5,000 for smaller straightforward projects to $30,000 or more for large or difficult houses. Blais Electric in Guelph quotes $12,000 to $35,000 or more for a full rewire, at $8 to $15 per square foot, and $18,000 to $35,000 or more specifically for knob-and-tube replacement. HomeGuide's American figures are higher per square foot, $5 to $17 US, with knob-and-tube replacement at $12,000 to $35,000 US, and Angi's 2026 calculator prices the wiring work alone at $2 to $4 US per square foot before permits and wall repair. The gap between Angi and HomeGuide is scope, not error: Angi prices the wiring, HomeGuide prices old-house work through finished walls with patching and code upgrades. The honest Canadian planning range is $8,000 to $15,000 for a small home, $10,000 to $30,000 for an average home, and $25,000 to $50,000 or more for a large or complex one, plus $2,000 to $8,000 for drywall repair and repainting that is often excluded from the electrical quote.

The decision rule starts with the insurer, not the electrician. Before you buy a house with knob-and-tube, get the insurer's answer in writing, because Ontario's Electrical Safety Authority says many insurers will not provide or renew coverage and some require full replacement first, and the same is true in British Columbia, where insurers may require a certified inspection or refuse new policies on homes with active knob-and-tube. If you already own the house, ask the insurer what it needs: an inspection certificate, a replacement deadline, or a higher premium. Then get the electrician's answer in writing too, after an inspection that checks the visible wire condition, the fuse or breaker protection, and whether any outlets have been added to the old circuits, because the ESA says existing concealed knob-and-tube can stay only if it is protected by a 15-amp fuse or breaker, no outlets have been added, and the visible wire is in good condition. The ESA also lists the owner workarounds that make old wiring dangerous: a 20-amp or 30-amp fuse screwed in where a 15-amp belongs, extension cords used as permanent wiring, and ground pins snapped off plugs.

Never insulate over live knob-and-tube. The wires were designed to dissipate heat in open air, and burying them in insulation removes that cooling, which is why a rewire is usually scheduled before an attic insulation upgrade, not after. A full rewire is also usually paired with a service upgrade, because knob-and-tube houses frequently still run on 60-amp service, and the rewire is the moment to go to 100 or 200 amps. A permit is required, and in Calgary and Edmonton a homeowner cannot get one for concealed wiring, so the work goes to a licensed electrician. Get three written quotes that each list the circuits, the panel work, the permit, the inspection, and whether drywall repair is included, and compare them line by line. Our guide Electrical Panel Upgrade Cost: 100A to 200A in Canada covers the service upgrade that usually rides along, and Aluminum Wiring Remediation Cost in Canada covers the other legacy wiring problem of the same era. For a rough budget before you call, the RepairPrice home calculator (home-calculator.php) gives a fair range for your city.

Common questions:

Q: Is knob-and-tube wiring dangerous? A: Not inherently by design, but it is 80 to 100 years old, it has no ground wire, its cloth insulation becomes brittle, and it was designed for loads far smaller than a modern home. The ESA says it is safe provided it is properly maintained, protected by a 15-amp fuse or breaker, with no added outlets and visible wire in good condition. The danger comes from what has been done to it since: oversized fuses, bad splices and insulation blown over it.

Q: Will insurance companies cover a home with knob-and-tube wiring? A: Many will not write a new policy, or will only insure with an exclusion for electrical fire, or will require an inspection and a replacement deadline. The Insurance Bureau of Canada says insurers will ask about it and may require updated wiring, a minimum 100-amp service or an inspection. Get the insurer's answer in writing before you buy.

Q: How much does it cost to replace knob-and-tube wiring in Canada? A: NoRadiation estimates $8,000 to $15,000 for a typical home and $25,000 to $50,000 or more for large or complex homes, at $10 to $22 per square foot. Blais Electric in Guelph quotes $18,000 to $35,000 or more for knob-and-tube replacement specifically, plus $2,000 to $8,000 for drywall repair and repainting.

Q: Does knob-and-tube have to be removed by law? A: No. The code is not retroactive: the ESA says existing concealed knob-and-tube can stay if it is protected by a 15-amp fuse or breaker, no outlets have been added, and the visible wire is in good condition. In practice insurers, buyers and plans to insulate the attic are what force the replacement.

ScopeTypical range (CAD)Notes
Small home / partial rewire8,000–15,000Limited circuits, good access
Average home full rewire10,000–30,000Circuits, access and finishes drive cost
Large / complex home25,000–50,000+Finished walls, many circuits
Drywall repair + repainting2,000–8,000 extraOften excluded from electrical quote

About the author

Oleksandr Potapenko

Oleksandr Potapenko β€” founder of RepairPrice, a Canadian price-transparency platform for car and home repairs, based in Edmonton, Alberta.

Check the fair price

See what this repair should cost for your car in seconds.

→

Check my quote

Got a number from a shop? Find out in 30 seconds if it is fair.

→

Related guides