Trailer Hitch Installation Cost in the USA

By Oleksandr Potapenko · 2026-11-16 · How we research prices

Mechanic installing a trailer hitch receiver on the rear frame of a pickup truck in a US auto shop

The bottom line: installing a trailer hitch in the USA typically costs $300–$650 for a basic vehicle-specific receiver with professional labour, according to ThePricer.org. U-Haul, which calls itself America’s number-one hitch installer, quotes a broader $100–$600 installed, while AutoZone cites $250–$1,300 or more — and the gap is real, not a mistake. The low end is a simple bolt-on receiver on a truck or SUV with pre-drilled frame holes; the high end is a vehicle that needs bumper trimming, exhaust work, a 7-pin harness and a brake controller. A towing-ready setup with 4-pin lighting wiring, a ball mount, hitch ball and locking pin commonly reaches $500–$900, and a 7-pin setup with a brake controller runs $800–$1,500. Fifth-wheel and gooseneck systems for pickups are a different job entirely at $1,200–$3,000 or more.

Why do the sources disagree so much? Because they are pricing different jobs. This Old House’s 2026 guide puts most receiver hitches at $150–$400 for parts, with shop labour of $75–$150, which lines up with U-Haul’s published receiver prices of roughly $195–$215 plus about $100–$200 in labour. AutoZone’s $250–$1,300+ ceiling includes dealer-style installs, complex vehicles and full wiring packages, while ThePricer.org’s $300–$650 is the middle of the road for a standard receiver installed by a pro. The honest way to read a quote is to split it into three lines — receiver, wiring, labour — and compare each one, not just the total. A quote that looks cheap often excludes wiring, and wiring is where $200–$500 quietly appears.

How much does it cost to install a hitch on a Ford F-150? A full-size pickup is usually the easy case: the frame is hitch-ready, a Class III or IV receiver bolts on in 1–2 hours, and a basic installed receiver typically lands near the $300–$650 band, or $500–$900 with 4-pin wiring. A Honda CR-V or Toyota RAV4 is often the opposite — the bumper usually has to come off, the exhaust may need lowering, and some trims need a wiring module programmed to the car, which pushes labour and parts toward the top of the range. What hitch class do I need? Class I (up to 2,000 lbs gross trailer weight, 200 lbs tongue weight) suits bike racks and small utility trailers; Class II (up to 3,500 lbs) covers small campers; Class III (up to 8,000 lbs) is the standard for SUVs and half-ton trucks; Class IV/V and fifth-wheel or gooseneck hitches are for heavy trailers and full-size pickups. The class table below gives the tow ratings and typical installed prices.

The decision rule is simple: if the receiver bolts to existing frame holes with no wiring — a common case on trucks and older SUVs — a careful DIY install with a torque wrench can save $100–$200 in labour, and U-Haul even publishes DIY guides for it. Go professional when wiring is involved, when the bumper or exhaust must be moved, when a brake controller is needed, or when the vehicle is still under warranty and a dealer-installed OEM hitch protects it. Never let a hitch raise your expectations: a hitch does not increase your vehicle’s factory towing capacity — the usable limit is set by the lowest-rated part of the whole system, including the vehicle, receiver, ball mount, ball, coupler and tongue-weight limit. Before you pay, get the quote itemised, confirm whether wiring and the ball mount are included, and check the warranty — U-Haul offers an optional $5 lifetime warranty on its hitches. For a related check on what your vehicle needs before towing season, see “Wheel Alignment Cost in the USA”, and use the RepairPrice calculator (calculator.php) to compare the quote against fair local labour rates.

Hitch setupTow ratingTypical installed cost (USD)What it covers
Class I receiverUp to 2,000 lbs GTW$300–$450Light receiver for bike racks and small trailers
Class II receiverUp to 3,500 lbs GTW$350–$550Small campers and utility trailers
Class III receiverUp to 8,000 lbs GTW$400–$650Standard SUV and half-ton truck receiver
Receiver + 4-pin wiringPer receiver class$500–$900Receiver, wiring, ball mount, ball, locking pin
Receiver + 7-pin + brake controllerPer receiver class$800–$1,500Full towing setup with trailer brakes
Fifth-wheel / gooseneckUp to 16,000+ lbs GTW$1,200–$3,000+In-bed hitch for heavy trailers and RVs
DIY receiver only (parts)Per receiver class$150–$450Receiver and hardware, no labour or wiring
Labour only (pro install)—$75–$200Typically 1–3 hours, per U-Haul and AutoZone

About the author

Oleksandr Potapenko

Oleksandr Potapenko — founder of RepairPrice, a Canadian price-transparency platform for car and home repairs, based in Edmonton, Alberta.

Check the fair price

See what this repair should cost for your car in seconds.

→

Check my quote

Got a number from a shop? Find out in 30 seconds if it is fair.

→

Related guides